Skip to content

Types of Butterfly Valves (API 609)

Share on whatsapp
Share on telegram
Share on linkedin
Share on email

A butterfly valve is used to shut off or modulate the flow of a fluid (isolation and regulation). API 609 Centric butterfly valves (soft seated) are preferred to gate and ball valves for low-pressure and non-critical applications as they are cheaper, lighter and easier to install. Eccentric butterfly valves (double offset and triple offset valves) with metal seats have surged in popularity and compete with globe and ball valves for some applications.

WHAT IS A BUTTERFLY VALVE?

A butterfly valve is a regulating and shut-off device that can be an alternative, in some applications, with globe and ball valves.

This type of valve may be classified base on multiple parameters:

  • design: centric, double eccentric, triple eccentric
  • end connection type: wafer, lug (semi or full), flanged and double flanged
  • seat material: soft (example: Teflon, Buna, rubber, etc) or metal-to-metal (SS304, SS316)
  • body and disc materials (from cast iron to high nickel alloys)
  • actuation: manual (lever, gear, a worm gear) and actuated (electric, pneumatic, hydraulic and gas-over-oil types)

 

Butterfly valves can be used for a wide range of applications such as water supply, wastewater treatment, fire protection, for the chemical and oil industries, for fuel handling systems and also for applications within the power generation industry.

With the introduction of the double and triple eccentric designs, butterfly valves are more and more used also in the oil and gas industry and have started to compete with more traditional valves, as globe and ball valves.

BUTTERFLY VALVE WORKING PRINCIPLE

The key component of a butterfly valve is the disc, a metal ring which is positioned at the centerline of the pipe and connected to an external actuator (manual level or actuator) via a rod.

Compared to a ball valve, the disc of a butterfly valve is always in contact with the fluid conveyed by the pipeline and creates, therefore, a pressure drop.

In the closed position, the disc blocks the bore of the valve, and, in an open position, the disc allows the passage of the fluid.

A quarter turn movement is needed to switch the valve from a fully open to a fully closed position (and such movement can be executed as quickly as for ball valves).

     


(Source: GEMU Group Youtube Channel)

The butterfly valve symbol in P&ID diagrams is shown in this image

BUTTERFLY VALVE SPECIFICATION

The API 609, ASME B16.34 (pressure and temperature rating), API 598 (testing), ASME B16.5 and ASME B16.47 (flanged ends) and ASME B16.25 specifications cover the dimensions and the tolerances of butterfly valves for the petrochemical industry and piping applications.

BUTTERFLY VALVE DESIGN

A key first classification is between concentric or eccentric butterfly valve:

  • concentric butterfly valve: the stem is centered in the middle of the disc and the is disc centered in the bore
  • the eccentric butterfly valve (double offset and triple offset): have one or more stub shafts (stems) which are located in an offset position from the center of the valve. Eccentric butterfly valves are also defined as the double or the triple offset.
         
A concentric butterfly valve (left), a double offset butterfly valve (center), triple offset butterfly valve (right)

CONCENTRIC BUTTERFLY VALVE (CENTRIC)

The concentric butterfly valve is used in water and wastewater treatment plants, fire protection systems, and gas supply.

  • Water treatment
  • Water distribution
  • Pumping installations
  • Water transmission
  • HVAC
  • Aeration systems
  • Clean wastewater
  • Filter Installations
  • Pumping installations
  • Membrane installations
  • Fire Protection (indoor/outdoor)
  • Natural gas and flare gas

DOUBLE ECCENTRIC BUTTERFLY VALVE

Double eccentric butterfly valves find large application in underground water supply applications and compete with gate valves (especially in larger bore sizes) due to the fact that they are lighter, cheaper and minimize the excavation works.

TRIPLE ECCENTRIC BUTTERFLY VALVE

Triple offset butterfly valves are built with high-grade materials like stainless steel and duplex/super duplex steel and compete with ball valves in mission-critical applications with remarkable corrosion and high temperature/pressure. Triple offset butterfly valves are the most sophisticated type and are gaining market share in the latest years.

DOUBLE VS. TRIPLE ECCENTRIC BUTTERFLY VALVE

 .        
The images show the design difference between a double and a triple eccentric butterfly valve (respectively at the left and right side of the diagram).

MATERIALS FOR BUTTERFLY VALVES

VALVE BODY

Butterfly valves, like any other type of valve, are available in multiple materials and combinations of materials (body, disc, seat).

The selection of the materials is based on the fluid to be shut off, the pressure and the temperature of the application at hand. Here follows a list of the main materials used for butterfly valves, which are generally cast grades.

CARBON STEEL

Carbon steel is an iron and carbon alloy (no other alloying elements are added to control the properties of the material).

For butterfly valve construction, carbon steel is most often used to form the body and disc of the valve using the sand casting process.

The most common grade used for butterfly valve bodies and discs is ASTM A216 WCB and LCC (Low Carbon Content) steels  (which are cast steels). They are used, respectively, for high temperature and low-temperature service.

The main advantage of carbon steel (CS) butterfly valves is their relatively low cost combined with acceptable performance (especially for low-pressure applications). The weakness of carbon steel valves is their poor resistance to corrosion (which can be improved by applying external paints or internal lining materials as Teflon)

STAINLESS STEEL

Stainless steels are alloys of iron, nickel and, chrome (the min. content for Cr is 10.5%). The addition of chrome forms a self-healing layer of oxide on the surface of the material that protects it from rusting.

When the surface of a stainless steel made product is scratched, the chromium reacts with oxygen and prevents it the from reacting with iron and rusting. Many different types of stainless steels are available, generally called 300 and 400 series.

Stainless steels can be classified in ferritic, austenitic, martensitic, duplex and precipitation hardenable (14 Ph).

This classification is based on the microstructure of the material by varying the composition of the elements mixed. The most common SS types used for the construction of valves, in general, are the austenitic and the duplex grades.

AUSTENITIC STAINLESS STEEL

Austenitic stainless steels contain (in addition to Chrome), nickel, which has the effect of retaining the high temperature face-centered-cubic austenitic structure at temperatures where it would normally have transformed to the ferritic body-centered-cubic structure.

This face-centered cubic structure gives the material stronger toughness and ductility compared to ferritic grades.

Depending on the percentage of nickel contained, the tough austenitic structure can be retained even at very low temperatures, making the material suited for cryogenic applications.

The addition of molybdenum strengthens the resistance to pitting corrosion of the valve.

DUPLEX STEEL

Duplex stainless steels (UNS S32205 and UNS S31803) have a well-balanced structure of both the austenitic face-centered cubic and ferritic body-centered structure of iron.

This type of composition is obtained by controlling the alloying elements and the heat treatment executed on the alloy to manufacture a structure which consists of 50% austenite and 50% ferrite.

Duplex stainless steels combine the higher strength of the ferritic composition with the remarkable toughness of austenite.

The super duplex type (UNS S32750 and UNS S32760) contain higher levels of chromium and molybdenum to enhance the resistance to corrosion.

NICKEL ALLOY STEEL

Nickel alloys are used in for valves subject to very severe service conditions in terms of fluid, temperature and, pressure.

These alloys are particularly suited for extremely corrosive applications, which would break the protective oxide layer of lower grades steels (as stainless steel).

Inconel, Incoloy and, Hastelloy are the most used nickel-alloys used in valve construction. The main disadvantage of nickel alloys is their high weight and high cost (a multiple of stainless steel valves).

TITANIUM AND TITANIUM ALLOYS

Titanium alloys combine remarkable strength and lightweight with excellent resistance to corrosion.

Titanium alloys have the highest strength-to-weight ratio compared to any other metal. Similarly to stainless steels, titanium alloys feature a protective oxide layer on their surface which protect the product from rusting.

Titanium offers strong resistance to corrosion by seawater, in particular for environments where hypochlorite is present.

The main disadvantage of titanium alloys is their high price, a multiple of stainless steel, and the complexity of production process, due to the high reactivity of the metal (special casting procedures are required to prevent the reaction of titanium with oxygen during melting and pouring.

NICKEL ALUMINIUM BRONZE

This is a copper alloy which contains approximately 10% aluminum, 5% nickel and 5% iron. It features strong corrosion resistance, especially in seawater applications and resists the formation of a biofilm, a frequent cause of corrosion problems for stainless steels.

Butterfly valves API 609 may have soft or metal seats. Valves with soft seats are also called “soft-seated” or “resilient” butterfly valves and are of the centric type. Eccentric design (double or triple offset) are available, generally, with metal seat design, which could also be fireproof.

SEAT MATERIALS

SOFT (RESILIENT BUTTERFLY)

Soft seated butterfly valves (resilient) feature EPDM, VITON, NBR, BUNA-N, and similar soft seats. Soft-seat butterfly valves are generally of the concentric type and suit low pressure and non-critical applications

METAL SEATED BUTTERFLY VALVE

In this case, the body of the valve and the disc feature a metal-to-metal seal.

High-performance butterfly valves (double eccentric) are available both with soft and metal seats. Triple offset butterfly valves have, generally, a metal seat and an ATEX fire-safe protection.

 .     
Double offset and triple offset butterfly valve

Need Piping from Stock?

Submit your RFQ · Get an Offer · Receive Stock
SUBMIT RFQ

7 Responses

  1. Hi,Dear Sales Manager,

    How are you ? So glad your can open my email.We hope it is a good chance for both of us open the business cooperation.
    Tianjin Fortis valve co., LTD. Was set up in 2000, is located in Tianjin in northern of China. We have the advanced machining equipment and coating processing line, We have our own Machining shop, painting shop and assembled shop. We can ensure you the best price and delivery. We export to UK,Italy, Turkey, Russia, HK,Korea etc.

    Product Range:
    Butterfly Valves (wafer Type/ Lugged Type/ Double Flanged/Double eccentric and triple eccentric type)
    Dual Disc Check Valves
    Gate valves( soft seat )

    Standard: DIN PN10/PN16, ANSI150,BS 10,TABLE E, JIS 10K etc.

    Material: Ductile Iron, Cast Iron, CF8(SS304),CF8M(SS316),2207/2507,Aluminum bronze ,Carton Steel etc.

    Thanks for your time again and Really hope we can have the chance to do business the basis of equality and mutual benefit.

    Best Regards,
    Alice Summer
    Mobile/Whatsapp+8615522861153
    Email:[email protected]
    Tianjin Fortis Valve Co., Ltd.

  2. Looking for Double eccentric butterfly valve
    Body in doube flanged Duplex St st
    Disc in Duplex st st
    Shaft in Duplex st st

    sizes 300 mm to 1200 mm
    PN 16
    medium is seawater

  3. Hi Sr.

    I am looking for a 4 inch normally closed flange butterfly fire safe valve
    with independent hydraulic actuator (internal storage and manual reset)
    12,5 Bar. This is for a fuel loading skid, as a fire protection.

    What do you recommend: Flanged? Double offset? Triple offset?

  4. BALL VALVES
    BUTTERFLY VALVES ( Manual/Gear operated/Motorised)
    DAMPER VALVE ( Manual/Gear operated/Motorised/Pneumatic)
    KNIFE EDGE GATE VALVES ( Manual/Gear operated/Motorised/Pneumatic)
    GATE VALVE ( Manual/Gear operated/Motorised)
    CHECK VALVE
    CONTROL VALVES
    SAFETY VALVES
    FOOT VALVE
    PFA/PTFE LINED VALVES

    VISIT OUR WEBSITE: http://www.hubluxe.com

    MOB.NO.8652075992

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Share on whatsapp
Share on telegram
Share on linkedin
Share on email

Need Piping from Stock?

Submit your RFQ · Get an Offer · Receive Stock
SUBMIT RFQ

SHOP.PROJECTMATERIALS.COM

Buy Online!

ANSI Y-Strainers

Stock Delivery

EU Origin

 Factory Prices

 Top Quality

SIZES       ⅜” to 12″
RATINGS 150# · 300# · 600# · 800#
GRADES  Carbon · Stainless
ENDS        Flanged RF · BW · THD · SW

Eccentric Butterfly Valve